Event ID overview
The following table contains the most important event IDs of the device in ascending order.
–
Clicking the event ID shows you a detailed description of the event.
–
If the device displays an "internal event" that is not listed here, restart the device. If the event persists, make a note of the event ID and contact the manufacturer.
|
Event ID
|
Event
|
Severity
|
Configurable in
|
|
|
CiA: Continuous over current (internal)
|
Fault
|
-
|
||
|
Short circuit or earth leakage at the motor end
|
Fault
|
-
|
||
|
Short circuit at the motor end
|
Fault
|
-
|
||
|
CiA: i²xt overload (thermal state)
|
Fault
|
|||
|
Fault - Device utilization (ixt) too high
|
Fault
|
|||
|
Warning - Device utilization (ixt) too high
|
Warning
|
-
|
||
|
Clamp responded too often
|
Fault
|
-
|
||
|
SL-PSM stall detection active
|
Trouble
|
-
|
||
|
Maximum current reached
|
Information
|
-
|
||
|
Mains phase fault
|
Fault
|
-
|
||
|
UPS operation active
|
Warning
|
-
|
||
|
Fault - DC bus overvoltage
|
Fault
|
-
|
||
|
DC bus overvoltage warning
|
Warning
|
-
|
||
|
Fault - DC bus undervoltage
|
Trouble
|
-
|
||
|
DC bus undervoltage warning
|
Warning
|
-
|
||
|
DC-bus voltage to low for power up
|
Warning
|
-
|
||
|
Fault - Power unit overtemperature
|
Fault
|
-
|
||
|
Fault - Heat sink temperature sensor
|
Fault
|
-
|
||
|
Heat sink fan warning
|
Warning
|
-
|
||
|
PU overtemperature warning
|
Warning
|
-
|
||
|
External supply voltage critical
|
Warning
|
-
|
||
|
Overload 24 V supply
|
Warning
|
-
|
||
|
OEM hardware incompatible
|
Fault
|
-
|
||
|
Warning - Internal fan
|
Warning
|
-
|
||
|
Trigger/functions connected incorrectly
|
Trouble
|
-
|
||
|
User-defined fault 1
|
Fault
|
-
|
||
|
User-defined fault 2
|
Fault
|
-
|
||
|
Warning invert rotation
|
Warning
|
-
|
||
|
Maximuml allowed troubles exceeded
|
Fault
|
-
|
||
|
User-defined fault (LECOM)
|
Fault
|
-
|
||
|
Network: user fault 1
|
Fault
|
-
|
||
|
Network: user fault 2
|
Fault
|
-
|
||
|
NetWordIN1 configuration incorrect
|
Trouble
|
-
|
||
|
CU: load error ID tag
|
Fault
|
-
|
||
|
PU: load error ID tag
|
Fault
|
-
|
||
|
Power unit unknown
|
Fault
|
-
|
||
|
Assertion level monitoring (Low/High)
|
Fault
|
-
|
||
|
Fault - Analog input 1
|
Fault
|
|||
|
Analog input 2 fault
|
Fault
|
|||
|
Analog output 1 fault
|
Warning
|
-
|
||
|
Analog output 2 fault
|
Warning
|
-
|
||
|
Fault - Pole position identification
|
Fault
|
|||
|
Motor overcurrent
|
Fault
|
|||
|
Memory module is full
|
Warning
|
-
|
||
|
Memory module not present
|
Fault
|
-
|
||
|
Invalid user data
|
Fault
|
-
|
||
|
Data not compl. saved before powerdown
|
Warning
|
-
|
||
|
Network - Configuration error
|
Fault
|
-
|
||
|
Memory module: invalid OEM data
|
Warning
|
-
|
||
|
Memory module: wrong type
|
Fault
|
-
|
||
|
EPM firmware version incompatible
|
Fault
|
-
|
||
|
EPM data: firmware type incompatible
|
Fault
|
-
|
||
|
EPM data: new firmware type detected
|
Fault
|
-
|
||
|
EPM data: PU size incompatible
|
Fault
|
-
|
||
|
EPM data: new PU size detected
|
Fault
|
-
|
||
|
Invalid parameter changeover configuration
|
Warning
|
-
|
||
|
EPM data: unknown parameter found
|
Information
|
-
|
||
|
Parameter changes lost
|
Fault
|
-
|
||
|
Time-out (PAM)
|
No response
|
|||
|
BACnet time-out
|
Fault
|
0x2856:001
|
||
|
CAN: bus off
|
Trouble
|
|||
|
CAN: warning
|
Warning
|
|||
|
CAN: heartbeat time-out consumer 1
|
Fault
|
|||
|
CAN: heartbeat time-out consumer 2
|
Fault
|
|||
|
CAN: heartbeat time-out consumer 3
|
Fault
|
|||
|
CAN: heartbeat time-out consumer 4
|
Fault
|
|||
|
Modbus: network time-out
|
Fault
|
|||
|
Modbus: incorrect request by master
|
Warning
|
-
|
||
|
CAN: RPDO1 time-out
|
Fault
|
|||
|
CAN: RPDO2 time-out
|
Fault
|
|||
|
CAN: RPDO3 time-out
|
Fault
|
|||
|
Torque limit reached
|
No response
|
|||
|
Function not allowed in selected operating mode
|
Warning
|
-
|
||
|
Keypad removed
|
Fault
|
-
|
||
|
Safety option - Internal error
|
Fault
|
-
|
||
|
Motor overspeed
|
Fault
|
|||
|
Motor phase missing
|
No response
|
|||
|
Motor phase failure phase U
|
No response
|
|||
|
Motor phase failure phase V
|
No response
|
|||
|
Motor phase failure phase W
|
No response
|
|||
|
Motor parameter identification fault
|
Fault
|
-
|
||
|
FMF Error
|
Fault
|
-
|
||
|
Cascading overload
|
Warning
|
-
|
||
|
Automatic start disabled
|
Fault
|
-
|
||
|
Load loss detected
|
No response
|
|||
|
Motor overload
|
No response
|
|||
|
Maximum motor frequency reached
|
Warning
|
-
|
||
|
Manual mode disabled
|
Warning
|
-
|
||
|
Manual mode activated
|
Warning
|
-
|
||
|
Manual mode time-out
|
Fault
|
-
|
||
|
Wrong password
|
Warning
|
-
|
||
|
Warning
|
Warning
|
-
|
||
|
Fatal Error
|
Fault
|
-
|
||
|
Keypad full control active
|
Warning
|
-
|
||