Trigger list
The trigger list lists all selection options (triggers) for the functions which can be configured using the parameters 0x2631:xx (P400.xx).
|
Selection
|
Information
|
|
|
0
|
Not connected
|
No trigger assigned (trigger is constantly FALSE).
|
|
1
|
Constant TRUE
|
Trigger is constantly TRUE.
|
|
11
|
Digital input 1
|
State of X3/DI1, taking an inversion set in 0x2632:001 (P411.01) into consideration.
|
|
12
|
Digital input 2
|
State of X3/DI2, taking an inversion set in 0x2632:002 (P411.02) into consideration.
|
|
13
|
Digital input 3
|
State of X3/DI3, taking an inversion set in 0x2632:003 (P411.03) into consideration.
|
|
14
|
Digital input 4
|
State of X3/DI4, taking an inversion set in 0x2632:004 (P411.04) into consideration.
|
|
15
|
Digital input 5
|
State of X3/DI5, taking an inversion set in 0x2632:005 (P411.05) into consideration.
|
|
50
|
Running
|
TRUE if inverter and start are enabled and output frequency > 0 Hz. Otherwise FALSE.
Exception, quick stop mode: TRUE if inverter and start are enabled and output frequency > 0.2 Hz. Otherwise FALSE.
|
|
51
|
Ready for operation
|
TRUE if inverter is ready for operation (no error active and DC-bus voltage ok). Otherwise FALSE
|
|
53
|
Stop active
|
TRUE if inverter is enabled and motor is not started and output frequency = 0.
|
|
54
|
Quick stop active
|
TRUE if quick stop is active. Otherwise FALSE.
|
|
58
|
Device warning active
|
TRUE if warning is active. Otherwise FALSE.
–
A warning has no impact on the operating status of the inverter.
–
A warning is reset automatically if the cause has been eliminated.
|
|
59
|
Device trouble active
|
TRUE if a fault is active. Otherwise FALSE.
–
In the event of a fault, the motor is brought to a standstill with the quick stop ramp. The inverter is then disabled.
–
Exception: In case of a serious fault, the inverter is disabled immediately. The motor has no torque (coasts).
–
The error state will be left automatically if the error condition is not active anymore.
–
The restart behaviour after trouble can be configured.
 Automatic restart after a fault |
|
60
|
Heatsink temperature warning active
|
TRUE if current heatsink temperature > warning threshold for temperature monitoring. Otherwise FALSE.
–
Display of the current heatsink temperature in 0x2D84:001 (P117.01).
–
Setting of the warning threshold in 0x2D84:002.
|
|
68
|
Stop command active
|
TRUE if delay to standstill active. Otherwise FALSE.
|
|
69
|
Rotational direction reversed
|
TRUE if output frequency is negative. Otherwise FALSE.
|
|
70
|
Frequency threshold exceeded
|
TRUE if current output frequency > frequency threshold. Otherwise FALSE.
–
Display of the current output frequency in 0x2DDD (P100.00).
–
Setting Frequency threshold in 0x4005 (P412.00).
|
|
71
|
Actual speed = 0
|
TRUE if actual output frequency = 0 Hz (
± 0.3 Hz), irrespective of the operating mode. Otherwise FALSE. |
|
78
|
Current limit reached
|
TRUE if current motor current
≥ maximum current. Otherwise FALSE.–
Display of the present motor current in 0x2D88 (P104.00).
–
Setting for the maximum current in 0x6073 (P324.00).
|
|
79
|
Torque limit reached
|
TRUE if torque limit has been reached or exceeded. Otherwise FALSE.
–
Setting "Actual positive torque limit" in 0x2949:003 (P337.03).
–
Setting "Actual negative torque limit" in 0x2949:004 (P337.04).
|
|
81
|
Error of analog input 1 active
|
TRUE if the monitoring of the input signal at the analog input 1 has responded. Otherwise FALSE.
This trigger is set as a function of the following settings:
–
Monitoring threshold 0x2636:008 (P430.08)
–
Monitoring condition 0x2636:009 (P430.09)
The setting of the Error response in 0x2636:010 (P430.10) has no effect on this trigger.
|
|
82
|
Error of analog input 2 active
|
TRUE if the monitoring of the input signal at the analog input 2 has responded. Otherwise FALSE.
This trigger is set as a function of the following settings:
–
Monitoring threshold 0x2637:008 (P431.08)
–
Monitoring condition 0x2637:009 (P431.09)
The setting of the Error response in 0x2637:010 (P431.10) has no effect on this trigger.
|
|
83
|
Load loss detected
|
TRUE if actual motor current < threshold for load loss detection after delay time of the load loss detection has elapsed. Otherwise FALSE.
–
Display of the actual current in 0x6078 (P103.00).
–
Setting Threshold in 0x4006:001 (P710.01).
–
Setting Delay time in 0x4006:002 (P710.02).
|
|
84
|
Heavy load monitoring
|
TRUE if the actual apparent current of the motor exceeds the threshold for longer than the delay time.
FALSE if the actual apparent current of the motor falls below the threshold value minus 5 % (hysteresis).
|
|
102
|
Sequence suspended
|
Status signal of the "sequencer" function:
TRUE if the sequence is currently suspended.
|
|
103
|
Sequence done
|
Status signal of the "sequencer" function:
TRUE if the sequence is completed (final segment has been passed through).
|
|
104
|
Local control active
|
TRUE if local keypad control
("LOC") active. Otherwise FALSE.
|
|
105
|
Remote control active
|
TRUE if remote control ("REM") via
terminals, network, etc. active. Otherwise FALSE.
|
|
106
|
Manual setpoint selection active
|
TRUE if manual setpoint selection ("MAN") via keypad active. Otherwise FALSE.
|
|
107
|
Automatic setpoint selection active
|
TRUE if automatic setpoint selection
("AUTO") via terminals, network,
etc. active. Otherwise FALSE.
|
|
201
|
Internal value
|
Internal values of the manufacturer.
|
|
202
|
Internal value
|
|
|
203
|
Internal value
|
|
|
204
|
Internal value
|
|
|
205
|
Internal value
|
|
|
206
|
Internal value
|
|